Precautions of Cold Rolling Mill

1. Preparation for Startup

Let the rolling mill equipment idle for about 10 minutes. During this period, observe whether the device is running normally, and add lubricating oil and rolling oil to lubricate the equipment properly according to the regulations.

2. Precautions before Unloading

(1) The press should be raised to the specified position, the reel should be retracted into position, and the hydraulic truck should be prepared in advance for auxiliary discharge.

(2) The aluminum plate plug should be inserted into the jaws successfully, otherwise, it will be difficult to insert.

3. Some Considerations

(1) The time for each jog of the machine should not exceed one second. The turbine should be adjusted to reduce the turbine. The adjustment amount on both sides should be equal to avoid the side bend of the rolled piece.

(2) When the cold rolling mill is running, someone should be responsible for guarding to prevent problems.

(3) Generally speaking, the thickness of one rolling of a single cold rolling mill should not exceed 40% of the aluminum plate.

(4) There should be no debris in the production line.

(5) Appropriate adjustments should be made to the pass and reduction depending on the material of the incoming material and the capacity of the rolling mill.

(6) The use of cold rolling mills should meet the requirements of the main technical parameters and should not be overloaded.

(7) The mill roll should not have serious wear and should be replaced if necessary.

(8) In the rolling process, if the wear of the mill roll has affected the surface quality and dimensional accuracy of the rolled piece, the roll should be changed immediately. After changing the roller, it should idle for 2 to 3 minutes.

(9) If there is any phenomenon such as tearing or skewing of the rolled piece, the hand can not be used. It should be stopped first and then taken out.

(10) Rolled finished products or semi-finished products should be filled out with relevant records and stacked in batches.

How to Improve the Operation Efficiency of High-speed Rolling Mill?

High-speed rolling mill is similar to the conventional rolling mill. The ultimate goal is to obtain the required size of the rolled piece by rolling mill calendering. In rolling operation, in order to improve the operation efficiency of the high-speed rolling mill, it is necessary to take corresponding improvement measures.

       

The operation efficiency of high-speed rolling mill is mostly affected by unplanned parking, other equipment delays, roll and bearing replacement, and other process maintenance. Therefore, we need to improve the operation efficiency of the high-speed rolling mill in a planned way. The specific operations are as follows:

1. The material of rolls should be screened according to the requirements of the rolled parts to improve the fatigue strength and service life of the rolls. 

2. Inspect the wear of roll and guide from time to time.

3. Inverse injection process of bearing lubricant from inside to outside to inside, so as to reduce the pollution of dust to bearing.

4. Using ultrasonic technology to inspect and analyze rolls.

5. The dry lubricating oil point has been modified. At present, the dry oil is added from the high-pressure zone. The amount of added oil increases from six cycles of raw materials to eleven cycles, and the thin oil lubrication is a 15-minute cycle. The cumulative effect of these changes can reduce the bearing temperature by several degrees Celsius.

With the upgrading of the steel rolling industry, new problems will arise, and we need to optimize and adjust the rolling process according to the actual situation at any time. This process requires us to explore step by step for a long time.

If you are interested in our rolling mill machine, please feel free to mail at marketing2@hanrm.com, we will make the customized solution for you.

How to Carry out Daily Maintenance of Rolling Mill?

Rolling mills are widely used in the steel industry. In order to ensure the smooth running of daily work, daily maintenance is particularly important. It should be noted that the daily maintenance of the rolling mills will affect the service life. So how to carry out the daily maintenance of the rolling mill, how to operate?

Every day, the rolling mill is inspected for oil, water and gas leakage and overheating of the machine parts; reducing the loss caused by the illegal operation of the equipment or maintenance, and when lifting the rubber rolls, take necessary maintenance measures at the chain, rope and end of the roll surface.

The automatic thickness control system on the rolling mill is operated strictly in accordance with the rolling mill operating process and operating methods. The gearbox should be cleaned at least once a quarter. When the roll is fed to the extreme position, special attention must be paid to the safe operation of the rolling mill. Care should be taken when performing the rolling mill operation to prevent the hand from being pressed by the steel plate and being fed together with the steel. When using the aircraft hoisting mill for inspection, be careful not to collide with the machine.

In the rolling operation, the personnel of each department should coordinate with each other and listen to the command of the person in charge of the rolling mill production line. In the rolling process, the roller and the raceway are in line contact or repaired line contact, and the radial bearing capacity is large and is suitable for bearing heavy load and impact load. If irregular noise is found, such as the abnormal phenomenon that the roller cannot be touched by the sudden release of the load after the steel bar is interrupted, it should be stopped immediately and checked, and the steel rolling production line can be completely stopped before being repaired. After the main drive of the motor is stopped, the upper and lower rolls can be lifted and lowered. When cleaning, firstly, in the hot state, stop the oil drain screw on the side of the gearbox, and turn the rollover of the roll and the lifting of the upper roll.

After the end of rolling, the finished material should be cleared, and the equipment maintenance and repair work should be done. In order to strengthen the effective management of the equipment, the equipment utilization rate should be improved, and the power supply should be turned off in time.

The Adjustment of Steel Rolling Mill

Before the steel rolling mill is used, the roll pass, controlling plate shape and backup roll should be adjusted according to the requirement; and the fixed position of the rolls in the rolling mill should be maintained. The workload of the roll bearing is heavy and varies greatly, so the friction coefficient of the bearing is required to be small.

After determining the product rolled by the rolling mill, the line speed of the rolling mill can be basically determined. The hardness of the raw materials is measurable. The rolling stock of the rolling mill is determined by changing the plastic deformation size.
Usually, the newly installed steel rolling mill has a running-in process. During the running-in process, the rolls are operated in a second operation, and the operation speed is 50%, 65%, 75%, and 85%. Different steel rolling mill models use the rolls with different materials and specifications for different rolling products.

After the steel rolling mill is installed, the gears of the reducer and the gearbox need to have meshed, the rolling speed is too fast, and the torque is enhanced. After the normal operation of the rolling mill for 30 days, stop the rolling mill and check the meshing of the large and small gears, and waits for everything to be normal, the rolling speed can be increased.

Under normal circumstances, it is not necessary to adjust the rolling speed. The rolls in the steel rolling mill is constantly worn during the running process. In order to keep the rolling mill stable in the controlled rolling requirements, the roll must be repaired in time, and the rolls need to be replaced in serious cases.

The steel rolling mill needs labor, even the automated equipment needs to be monitored manually in the console. The conveyor roller and shearing machine located in the automatic rolling mill must be strictly controlled during operation to avoid the failure of stacking steel or jamming. If the wear of roll and guide exceeds the specified range, it needs to be replaced. 

The rolling of the billet causes the roll to be squeezed instantaneously, and the bearing is subjected to correspondingly high pressure, thereby affecting the product size of the rolled steel. We may also need to make in-depth improvements, but the ultimate goal is to get better steel rolling mill equipment.

We can supply rebar rolling mill and wire rod mill equipment designing, manufacturing, installation, and commission of the equipment with “turn-key” service.

We can also design, manufacture and revamp other non-standard equipment according to the requirements of users.

If interested, please mail at marketing2@hanrm.com or kerrirollingmill@gmail.com.

How to Package Steel?

Steel should be packaged according to national standards and contracting requirements. In general, the contents of the package are (except for special requirements in the contract):

(1) Profiled steel with a diameter or thickness of less than 30 mm and a thin plate with a thickness of less than 4 mm shall be delivered in bundles. Each bundle shall be of the same batch number, and each bundle shall be affixed with at least two signs. The nameplate shall indicate the manufacturer's name, steel number, furnace (can) number, specifications, etc.

(2) Steels with a diameter or thickness equal to or greater than 30 mm may be delivered in bundles or may not be delivered in bundles. For bundles of steel, each bundle shall be affixed with at least two signs, steel may not be stamped. Bundles of steel that do not carry signs should be stamped or marked on the top steel or plate of each bundle. Steel that is not bundled must be stamped on each steel or steel plate.

(3) After the steel is packaged (or not supplied in bundles), it shall be painted according to the relevant standards.

(4) Steel delivered in bundles, each bundle shall be bundled with wire at not less than two places.

(5) The weight of each bundle shall not exceed 80kg when manually loaded and unloaded, and shall not exceed 5t when mechanically loaded and unloaded. After the consent of the purchaser, the manual loading and unloading may not exceed 130kg per bundle, and the mechanical loading and unloading may not exceed 10t per bundle.

In order to facilitate the distinction and use, all kinds of steel should have the mark, that is, the stamp.

The stamp shall be applied to the end face of the steel or to the surface of the steel 100 mm from the end of the steel. The contents include steel grade, furnace number, tank number, spindle number, section number, etc. For steel stamps with a diameter or side length greater than 40 mm, it can be punched on the end face. For steel stamps with a diameter or side length of less than 40 mm, it can be hit on the end face, or on an iron plate, and the iron plate is hung on the steel.

We can supply rebar rolling mill and wire rod mill equipment designing, manufacturing, installation, and commission of the equipment with “turn-key” service.

We can also design, manufacture and revamp other non-standard equipment according to the requirements of users.

If interested, please mail at marketing2@hanrm.com.

Hot Rolling Principle of Rolling Mill

Hot rolling is based on slabs (mainly continuous casting billets), which are heated to form strips by roughing rolling mills and finishing rolling mills. The hot steel strip from the last rolling mill of the finishing mill is cooled to a set temperature by laminar flow, rolled into a steel coil by a coiler, and the cooled steel coil is subjected to different finishing operations according to different needs of users. Lines (flat, straight, cross-cut or slit, inspection, weighing, packaging and marking) are processed into steel, flat and slit steel strips.

Since hot-rolled steel sheet products have high strength, good toughness, easy processing and good weldability, they are widely used in shipbuilding, automobiles, bridges, construction, machinery, pressure vessels and other manufacturing industries.

With the increasing maturity of new technologies such as hot-rolling dimensional accuracy, plate shape and surface quality, and the advent of new products, hot-rolled steel sheets and strip products have become more and more widely used and are becoming more and more competitive in the market. Hot rolling steel products can be divided into ordinary carbon structural steel, low alloy steel, alloy steel according to its material and performance.
     

According to the use, hot-rolled products can be divided into cold forming steel, structural steel, automobile structural steel, corrosion-resistant structural steel, mechanical structural steel, a welded gas cylinder and pressure vessel steel, and pipeline steel.

The advantage of hot rolling is that it can eliminate certain defects in the cast metal, such as welding the pores, refining coarse grains and changing the distribution of inclusions. The compactness and mechanical properties of the metal are improved. Secondly, the raw material (steel ingot or billet) is increased in thermoplasticity, and the deformation resistance is lowered. Therefore, the amount of deformation can be increased during rolling, which is advantageous for improving productivity. In addition, due to the reduced metal deformation resistance, the requirements for the rolling equipment can be correspondingly lower, so that the cost of the equipment can be reduced and the energy consumption of the motor can be greatly reduced.　　

The disadvantage of hot rolling is that high-temperature rolling produces iron oxide scale so that the surface of the metal is not smooth and clean; the size of the product is not accurate enough, and the mechanical properties are not as good as cold working.

We can supply high-speed wire rod mill equipment designing, manufacturing, installation, and commission of the equipment with “turn-key” service.

We can also design, manufacture and revamp other non-standard equipment according to the requirements of users.

If interested, please mail at marketing2@hanrm.com.